• Electric fireplace light wont turn off

    Electric fireplace light wont turn off

    I have a charmglow 23in electric fireplace. Everything works fine but the heat. It powers up fine, fake flames work, it has a turn knob to set the temperature, but when I push the HEAT switch to ON, you can hear the heater working and see the heating coils turn red but within 15 - 20 seconds you hear a loud click noise and the coils turn off and no heat is produced.

    electric fireplace light wont turn off

    Does anyone know what this could be and what parts I might need to repair this. Thank you very much in advance. It is probably drawing too much current and is shutting down to keep from starting a fire or burning wiring up. The loud click could be an internal circuit breaker. You'd need a multimeter to verify how much power the unit is drawing, to see if it is trying to draw more amps than the circuit is designed for.

    Just a quick question - do you know if this unit is designed to run on a 15 amp circuit? And there shouldn't be any extension cords, or anything else on the circuit, at the same time. Which means you need an electrical schematic of the unit, and know how to troubleshoot it. I'd recommend first checking the requirements of the unit if this is a new unit, you can find it on the packagingthese can also be found on a data-plate, usually on the back of the unit.

    If all else fails, check the manufacturer's website - they may even have a troubleshooting guide, or a list of authorized service providers.

    The circuit breaker may be faulty but unlikely as it's doing the job it was installed to do. You are going to need an Amish electrician to come out and replace the blown components! Update: this is a fireplace that plugs directly into a wall outlet. Answer Save. Bub Lv 7.

    Yugioh 5ds episode 94

    Erika Lv 4. Dimplex Electric Fireplace Troubleshooting. Good Luck. Could be a number of things, just sorted out a similar problem with my boiler last night. Have you checked the fuse to see it's the correct ampage. Have you checked that the wiring is correct, a lose wiring will trip the circuit.

    Error 0x1007 hikvision

    If all else fails a drink for an sparky friend looks wanting. Good luck. How do you think about the answers? You can sign in to vote the answer. D2 Lv 6.

    electric fireplace light wont turn off

    Amy Lv 4. Still have questions? Get your answers by asking now.JavaScript seems to be disabled in your browser. You must have JavaScript enabled in your browser to utilize the functionality of this website. This entry was posted on October 17, by Adam S. If you have a standard Napoleon fireplace remote control and you can't get it to work with your fireplace watch our video above or use these simple troubleshooting steps to get it working again.

    Most often your receiver box will be located within the controls cavity of your fireplace, like it is here - check to make sure the wires are secured tight to the terminals. If your fireplace is working properly and your receiver box is in working condition you should be able to slide the slider switch on the receiver box to the "On" position and your fireplace should turn on. If it doesn't, you may need to have your fireplace serviced by a technician. The remote control transmitter and receiver box are both battery powered - check the batteries in your units to make sure they have a good charge and there isn't any damage from corrosion.

    Remove the batteries from both the remote transmitter and receiver box. After you've removed the batteries from both units, move the receiver switch to the "Off" position. After replacing the batteries in each unit, slide the receiver switch back to the "remote" position. If working properly, at this point the light on the receiver box will blink and beep twice.

    What Causes an Electric Fireplace to Stop Working?

    Immediately following the beeps - press the "On" button on your remote control and hold it down for seconds. This should produce 3 beeps from the receiver box to confirm it has captured the code from the remote control. This entry was posted in Troubleshooting on October 17, by Adam S. Fireplace Remote Controls. Mon-Fri CST View All. Buying Guides Troubleshooting How to Videos.

    Napoleon Fireplace Remote Troubleshooting. Step By Step Guide:. Leave a comment Please wait Recent Posts. Sign Up for Our Newsletter:. Join our community Facebook Twitter YouTube. About Us.

    Suite 1 North Liberty, IA All Rights Reserved. Powered by Speroteck.A fireplace is a place where we burn woods to get wormer feeling and heat our house. It works with a gas connection and very easy to use. The wall switch also makes it easy to navigate.

    Here we will explain the full process on how to turn on gas fireplace with a wall switch. To turn on your new Gas fireplace with wall switch, you can use those steps serially.

    Also, make sure that you follow every step with proper care. Every Gas fireplace comes with its user manual. You would get a free copy of manual with your fireplace. You should read the full manual carefully, before adjusting your fireplace.

    If you are unable to get a manual copy, then check the fireplace model and get it from online. You can also get important information at the back side of the control panel cover. It would be harmful if you toggle your gas fireplace options. Generally, the Gas fireplace has a control panel on it. The control panel helps users to manually control and manage the gas on your fireplace.

    Just locate the control panel that is attached to your Gas fireplace body.

    Why Your Electric Fireplace Stopped Working

    Most of the time, control panel set hidden by a cover. Just open the cover of the control panel. If you have found the control panel of the Gas fireplace, probably you would a knob. At the body of the knob, you will get Pilot, On and Off written on it. Once you get it, rotate it to set the knob off.

    Abhi pratap wiki

    Then wait for at least 5 or 6 minutes to let remaining gas out. Open all available doors and windows for better ventilation.

    But if you still getting the weird smell, you must leave the house and contact with your gas provider or call fire service. Locate the supply valve that is attached to the gas live. Generally, it gets colored in red or blue. When you got it, just twist the supply valve until it gets parallel to the gas line. It opens the path to enter the gas into the fireplace.

    You can also control gas supply by adjusting the supply valve according to the situation. If you are ready to ignite the fire pilot lite, rotate the knob to the Pilot position.Rotate image Save Cancel. Breaking news: See More. More Rules New Posts. Next Last. Gas fireplace- pilot lit, fireplace will not fire I'm hoping someone can steer me on the right course with an issue I am having with a gas fireplace.

    The pilot comes on nice and quickly, and stays on, but the fireplace will not light. At first I assumed the thermostat was not working as it's fairly old.

    I took it off, though, and touched the two wires together, and can hear a soft clicking sound from the fireplace. I hadn't heard that when using the thermostat, so possible the stat really is broken, but that doesn't change the fact that the fireplace won't light even when asked to. I cleaned up a bit around the contacts. The wires are connected. The screws are tight. I checked the thermopile and thermocouple and pilot nozzle, and they look relatively clean.

    I was thinking I knew basically how this thing operates, but then I realized that I don't, because I don't understand what the 'clicking' sound is. I know less than I thought I've come to this realization about something-or-other most days so far. Can someone help me out with this, and explain what is likely going on, and whether I should continue diagnostic and maybe try to repair, or just call a professional in?

    I guess that both the pilot and thermocouple and working fine and looks a healthy size. I guess that the wiring and contacts are sound since touching the two together produces a result the clicking. So, what am I missing?

    Is this still likely something and if so, likely what that needs a cleaning? Or will something need replacing that I should not attempt myself? Thanks in advance to any expert or expert DIYer who has some wisdom for me. Sometimes its just because the pilot isn't hot enough.

    After you lit the pilot did you turn the gas valve from "pilot" to "on"? I read in another thread I personally know nothing about these thingsthat if you have a light switch to turn it on and off, to go bonkers flicking the switch on and off for a minute.

    Something about a light switch being less than ideal for this application, and corrosion or something, If it DOES end up hurting to try, don't blame me. Just trying to help. I had this problem as well.

    I sprayed WD40 into the part where the flames are supposed to come out and it lit afterwards. My father thinks it could've been spiders or webs that were in there. Help an animal charity or sanctuary out today. Become a volunteer, advocate, foster a pet, or donate. They need you as much as you need them!Fireplaces are as homey as it gets.

    The biggest drawback about fireplaces is the mess created by burning wood. Keeping the fire stoked, while trying to keep the house clean is burdensome and time consuming.

    Brother mfc j4850w software

    Thankfully, you can have your fireplace without any of the aggravation. Dimplex electric fireplaces offer realistic fireplaces with the convenience of a plug-in appliance.

    They come in a variety of models, even corner units. For the occasional times when they need troubleshooting, follow a sequential process to identify and fix the problem.

    Confirm that the fireplace is installed on the electrically appropriate circuit. Make sure the heater is the only appliance on the circuit; it needs to be a amp dedicated circuit. Check this detail if the breaker kicks off every time you turn the unit on.

    electric fireplace light wont turn off

    Replace the remote if the unit comes on independently without your having turned it on. Other remotes in the home, or even next door if the next house is close enough, may share the same frequency; or the remote is sensitive to the other radio frequencies in the area. Replace the circuit board of the unit if the remote is not the problem. Check the power supply if the unit will not come on when you press the remote. Evaluate the appearance of the flame. Look for and replace the burned-out light bulbs if the ember bed does not flicker and glow, or the flame is not visible or bright.

    Replace the light harness and check for loose wiring. Check the remote if the fireplace won't turn off or on. Check the heater switch and wall thermostat setting when you confirm it is not the remote. Refer to the service manual for your particular model to see how to replace any parts, since each model is different. Replace the heater and blower if the odor persists beyond the first two or three times you use it, depending upon the amount of time you use it each time.

    If you have heat but no blower, or the reverse, you more than likely have a defective heater assembly; replace it. Be especially careful with wiring the fireplace in, being sure to leave no damaged wiring in place or loose connections. Chuck Brown is a freelance writer and former teacher and athletic coach. He has held professional stints as a business owner, personal fitness trainer, curriculum designer, website designer, market trader and real estate investor.

    Brown holds a bachelor's degree in English and a master's degree in Christian counseling.

    Why Did My Greystone Electric Fireplace Quit?

    By Chuck Brown. Hunker may earn compensation through affiliate links in this story. Step 1 Confirm that the fireplace is installed on the electrically appropriate circuit. Step 2 Replace the remote if the unit comes on independently without your having turned it on. Step 3 Check the power supply if the unit will not come on when you press the remote. Step 4 Evaluate the appearance of the flame. Step 5 Check the remote if the fireplace won't turn off or on. Tip If you have heat but no blower, or the reverse, you more than likely have a defective heater assembly; replace it.

    Warning Be especially careful with wiring the fireplace in, being sure to leave no damaged wiring in place or loose connections. Share this article. Chuck Brown.Electric portable fireplaces are a convenient way to warm a room, barn, patio, deck, or any other area. A portable fireplace allows you to heat a room where a traditional fireplace is not an option. Also, the portable fireplace adds ambiance, visual appeal, and warmth to any space.

    6 Tips for Troubleshooting Your Electric Portable Fireplace

    After deciding on an electric fireplace that you love, you want to enjoy it, not stress over it not working. Luckily, fixing your fireplace shouldn't be hard to do. When experiencing issues with an electric portable fireplace, there are a few steps that you can use to help diagnose and repair the issue of the unit.

    Because electric portable fireplaces run off electricity, the first place to check is in the power supply when the unit is not working.

    You can check this in one of two ways. If you have a voltage tester, you can easily check the power outlet for voltage to ensure there is power available in the outlet. Alternatively, you can also move the fireplace in the direction of another outlet that you know is functioning properly and plug it in there to test if it will turn on.

    Some electrical fireplaces require more power than a standard appliance. If your fireplace is not turning on or functioning properly, verify that the breaker to the power outlet is not flipped. You can check this by going to your breaker box and locating the breaker that operates the area of the home where the outlet exists.

    If the light or coloring of the fireplace is not working, you may need to replace the lightbulb inside the fireplace. The visual effect and color of the fire is created by a lightbulb that can burn out after extended use.

    To correct this problem, you may simply need to replace the lightbulb with a new one. If one side or half of the fireplace is brighter, this could also be an indication that you need to replace a bulb. If your fireplace has more than one bulb, make sure you replace the one that's burnt out with a light of the same wattage to ensure even lighting. Electric portable fireplaces have fuses in them that must be functional for the fireplace to heat properly.

    If the fireplace has lost its ability to heat, check the fuses to see if they are burned out before replacing pricier parts or the whole unit. The fuses are inexpensive and easy to replace. To replace the fuse, first make sure that your fireplace is completely off so that you do not get shocked. Then, open up the fuse box in your fireplace. Depending on your make and model, this might be located in a different place; however, many keep them in the back.

    The fuse will look like a clear cylinder with a filament inside. If the filament is broken a likely indicator of why your fireplace is not working it will look black or gray.

    When the heating function of the fireplace is not working as well as it should, you may need to inspect and clean the fan to repair the issue. The fan can become dirty, and it needs to be cleaned to ensure it functions properly. A build-up of dirt and debris could prevent the fan from spinning properly and lower the effectiveness of the fan.

    If all else fails, you should look at the manual that came with your model. While the above steps should help you diagnose your portable electric fireplace issues, some makes and models have their own specific functions that can only be diagnosed with the accompanying directions.

    We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation Login Register How-Tos. Written by Doityourself Staff. Reviewed by Paige Butterfield.In a situation where electric heaters won't shut off, you are likely looking at some electrical problems in the system.

    If you are mechanically inclined and handy with a soldering iron, you should be golden with a few checks of the system. It is good to have a voltage meter to check for lost power in the unit once you have the case open for inspection. Be sure you follow all safety precautions to avoid getting burns or electrical shock. Inside electric heaters is a coil, or thermal temperature gauge sensor.

    Electric Fireplace Remote Not Working: Troubleshooting Guide

    If this is not functioning properly, it will not detect that the heater has reached the desired temperature and shut off. This should be the first thing to be checked and replaced.

    It should be located close to the heater coils, but not so close that it gets incorrect readings from the heaters outputs. Crossed wires can cause the gauge to not function properly as well.

    You will want to check all connections and be sure that they are getting proper contact. Each individual part of these units, like the fan, heater coil, and temperature sensor run on their own circuit. One thing you can do with malfunctioning electric heaters is check the circuits on the main board for proper voltage transfers.

    Use a voltage meter to read the positive and negative poles of all your electrical connections. If you find areas that lose current, then the components could be burnt out, which will not allow electricity to be regulated or flow properly.

    This can inhibit the unit's shut off mechanism once it reaches core temperature. You can check with your unit's manufacturer to see what type of replacement parts you can purchase for replacement yourself. If you find spots in the circuit board that are not responding properly to the electrical checks, then it is likely that either a regulator is fried, or the actual circuit path on the board itself is.

    Look for burn marks or scarring of the board's surface for blown connections or components. The most common malfunction in electric heaters is that the temperature sensor simply wears out or breaks. These can be switched out as a replacement part on most units, and you can even integrate a sensor from another broken unit as a spare part. These devices are generally made with the same electrical input and output standards, making it easy to replace.

    You can check with the manufacturer to see if they sell replacement temperature sensors that will fix your problem. On older units, this sensor is a coil that looks like a spring, and if it is broken, it will not function properly.

    On spring sensors, you cannot simply repair this component.

    electric fireplace light wont turn off

    You will actually have to disconnect it and replace it with a functioning part. We welcome your comments and suggestions.

    All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation Login Register How-Tos. Written by Doityourself Staff. Check the System's Temperature Gauge Inside electric heaters is a coil, or thermal temperature gauge sensor.

    Test the Circuits with a Voltage Meter One thing you can do with malfunctioning electric heaters is check the circuits on the main board for proper voltage transfers. Is the Temperature Guage Snapped or Broken? Popular Articles. How to Repair an Electric Heater that Wo Troubleshooting Electric Heaters Emittin Troubleshooting Electric Heaters: No Hea Troubleshooting Electric Heaters: No Heat.


    Comments

    Leave a Reply

    Your email address will not be published. Required fields are marked *